KSD9700 thermal protection, temperature switches small, low-power motor coil temperature protection KSD9700 thermal protection by thermal PBT housing or metal, welded bimetal element silver alloy contacts, conductive frame, insulation mounts, static touch pad and heat resistant wires and other components. Fully enclosed structure allows components from contamination by dust or impurities, to prevent damage to the penetration of liquid paint and external forces. Because the shell is a metal conductor, when using the configuration thermal conductivity and temperature of the insulating sleeve. Current through the bimetallic element impedance, the case of non-normal operation, if the current increases or the ambient temperature rises to the set temperature, the bimetallic element moves quickly, open the contact, cut off the circuit. When the device is cooled to a safe temperature, contact automatically closed, return to normal working condition. Widely used in single-phase, three-phase motors due to overload, stall caused by overheating of the motor under the protection of non-work state, also applies to overheat protection and temperature control choke coil, spiral tubes and transformers and other electrical appliances in general. KSD9700 use a thermostat switch conditions, the relative humidity at -25 ℃ - + 125% 2, the atmospheric pressure: 86-106Kpa 3, Working Position: Any KSD9700 technical parameters of a thermal protection device, contact form: 1D or 1H 2, Touch Point load: 220VAC 5A / 10A or 24VDC 5A / 10A 3, Insulation resistance: normal temperature and humidity ≥100MΩ 4, the contact resistance: ≤ 100 mΩ 5, dielectric strength: ≥1000VAC 6, vibration intensity: 50HZ single 0.35mm 7, Impact strength: 150m / S2 8, Weight: <3g 9, life: ≥10,000 times three, specification data sheet ksd9700 thermostat switch thermostat thermal protector Model length (MM) Width (M) high (MM) 20 - steel 20 7.4 3.8 20 8.0 4.2 Plastic 20- 15- 15- plastic steel 15 15 7.2 6.7 3.2 3.8 Action Chart reset code to reset the temperature operating temperature operating temperature reset temperature code 40 40 ± 5 ℃ ≥30 ℃ 105 105 ± 5 ℃ 70 ± 12 ℃ 45 45 ± 5 ℃ ≥30 ℃ 110 110 ± 5 ℃ 75 ± 12 ℃ 50 50 ± 5 ℃ ≥30 ℃ 115 115 ± 5 ℃ 80 ± 12 ℃ 55 55 ± 5 ℃ ≥30 ℃ 120 120 ± 5 ℃ 85 ± 12 ℃ 60 60 ± 5 ℃ 40 ± 10 ℃ 125 125 ± 5 ℃ 90 ± 12 ℃ 65 65 ± 5 ℃ 45 ± 10 ℃ 130 130 ± 5 ℃ 95 ± 12 ℃ 70 70 ± 5 ℃ 50 ± 10 ℃ 135 135 ± 5 ℃ 100 ± 12 ℃ 75 75 ± 5 ℃ 55 ± 10 ℃ 140 140 ± 5 ℃ 105 ± 12 ℃ 80 80 ± 5 ℃ 60 ± 10 ℃ 145 145 ± 5 ℃ 110 ± 12 ℃ 85 85 ± 5 ℃ 65 ± 10 ℃ 150 150 ± 5 ℃ 115 ± 12 ℃ 90 90 ± 5 ℃ 70 ± 10 ℃ 155 155 ± 5 ℃ 120 ± 12 ℃ 95 95 ± 5 ℃ 75 ± 10 ℃ 160 160 ± 5 ℃ 125 ± 12 ℃ 100 100 ± 5 ℃ 80 ± 10 ℃ special specifications can be developed Notes 1, using contact temperature installation according to customer requirements, the product should be charged with snapping apparatus mounting surface. 2, not when you install the plastic or metal shell collapsed or deformed, so as not to affect performance. 3, metal products have added insulation jacket of the installation can not be removed without the external insulating sleeve or crushed, to avoid leakage, ensure safe use. 4, the product is not greater than 5A current of the circuit used, should be selected cross-section of copper wire connected to it 0.4-0.75㎜2. 5, the product should be less than 90% relative humidity, ambient temperature below 40 ℃ ventilated, clean, dry place to store non-corrosive gases.